-
Shopping - Boutique
Informations générales sur les conditions d'envoi et le statut d'une commande.
Lors d'un achat de plusieurs objets, les frais d'expédition sont additionnés. En cas d'envoi combiné de différents articles achetés et si applicable, un remboursement partiel des frais d'expédition peut vous être adressé (en fonction de votre commande en termes de destination et de poids total).
General information regarding shipping conditions and order status checking.
When purchasing several items, shipping costs are added. In case of combined shipping of several purchased items, and if applicable, a partial refund of the shipping cost may be sent to you (depending on your order in terms of destination and total weight).
Contenu du panier
Payment by Paypal
preferredVous pouvez acquérir divers objets, modélisés et imprimés en 3D par mes soins.
Les adaptateurs permettent par exemple d'améliorer votre setup d'astrophotographie.You can get several items, designed and 3d-printed by miself.
Lots of adapters allow you to improve your astrophotography setup.Les objets sont imprimés en PLA. Les données techniques relatives au matériau utilisé sont disponibles ici. La fiche de sécurité est disponible ici.
ATTENTION : Le matériau plastique utilisé pour imprimer les objets se ramollit à partir de 60°C. Sous l’action d’une charge, ils sont susceptibles de se déformer s’ils sont exposés à la chaleur du soleil ou à toute autre source de chaleur. Les objets sont conçus pour une utilisation nocturne uniquement. Ils ne doivent pas être stockés à la chaleur du soleil ou toute autre source de chaleur.
Le stockage d'un support pour objectifs doit se faire à l'abri du soleil et en position à plat, non monté sur un trépied ou une monture.Items are made of PLA. Technical datasheet of the material used is available here. Safety datasheet is available here.
CAUTION : The plastic material used to print the items has a softening temperature of 60°C. Under the action of a load, they are likely to deform if they are exposed to the heat of the sun or any other source of heat. The items are designed for night use only. They shall not be stored in the heat of the sun or any source of heat, otherwise they will deform. Storage of the brackets must be done out of the sun in a flat position, not mounted on a tripod or a mount.
More than 1000 mounts improved in 50 countries.
-
Par astrokraken le 12 Février 2024 à 19:34
-
Par astrokraken le 11 Février 2024 à 22:31
Improve your focus tune and use your Maksutov
at its maximum of performanceNew : Tri-bahtinov mask !
Improve your focus tune and your collimation.
Shipping worldwide : + 6 €
-
Par astrokraken le 10 Février 2024 à 08:35
Available with Ring's bottom nuts size :
- M4
- 1/4'' UNC (Kodak)
Now available : Tri-bahtinov mask dewshield cap
-
Par astrokraken le 9 Février 2024 à 09:14
Original design : with M4 fixing nuts
Now available with Ring's bottom nuts size :
- M4
- 1/4'' UNC (Kodak)
-
Par astrokraken le 8 Février 2024 à 11:06
-
-
-
Par astrokraken le 20 Février 2023 à 22:26
-
Par astrokraken le 20 Février 2023 à 06:17
Want to find out more ? Click on the pictures !With its hinged rings, you can mount
this micro-focuser on your telephoto-lens
even with your dslr or CCD camera in place.
The rings fit from Diameter down to Diameter minus 30mm.
Telephoto-lens and dslr are not included
Worldwide shipping : + 15 €
-
Par astrokraken le 29 Janvier 2023 à 05:30
Light and short : this bracket is for
your Orion 50mm mini-guidescope
Shipping worldwide : + 18 €
-
Par astrokraken le 29 Mai 2021 à 07:45
With this polyvalent base, you can attach your Telrad finder
on several types of fasteners :
- piggyack mounting on your telescope's rings,
- Vixen-like dovetail fastener,
- finderscope dovetail.Want to find out more ? Click on the pictures !
Rings, Vixen dovetail and Telrad not included.
Worldwide shipping : + 3 €
-
Par astrokraken le 29 Mai 2021 à 07:39
Want to find out more ? Click on the pictures !
The special design of this mask makes it
"clipsable" on your lens.Once clipsed, it remains in place whatever
the orientation of your lens.
Shipping worldwide : +3 €
-
Par astrokraken le 29 Mai 2021 à 06:01
Want to find out more ? Click on the pictures !This bracket allows to attach a laser pointer
with a diameter of 12 to 22 mm
to the hotshoe of your dslr.$16 €
Worldwide shipping : 8 €
-
Par astrokraken le 29 Mai 2021 à 05:01
Mount two teleconverters together
to make a wide-field x1.5 binocular.Want to find out more ? Click on the pictures !
-
Par astrokraken le 29 Mai 2021 à 04:12
Original design with hinged rings !
Attach your Nikkor 300mm f/4 ED-IS AF-S
telephoto lens to the Vixen dovetail
of your equatorial mount.Add easily a guidescope or a red-dot finder atop
the bracket.Want to find out more ? Click on the pictures !
Telephoto lens, guidescope, autoguider, red-dot finder, dslr, and mount are not included.
Worldwide shipping : + 28 €
partially refunded in the following cases
- shipping to France : -15 €
- shipping to European Union : -8 €
-
Par astrokraken le 29 Mai 2021 à 03:00
Want to find out more ? Click on the pictures !
Especially designed for the
CELESTRON Mak 90
(telescope model : see pictures),
this mask is easy to attach and detach.Ideal accessory for deep-sky photography
with your preferred telescope !Worldwide shipping : +5 €
-
Par astrokraken le 4 Août 2019 à 22:04
-
Par astrokraken le 3 Juin 2018 à 18:30
-
Par astrokraken le 15 Avril 2018 à 10:03
Want to find out more ? Click on the pictures !
Attach your Polemaster+QHYCCD dovetail
on a iOptron Skytracker nomadic mount.Only a few seconds are enough to attach or detach it.
Very usefull if you need to share a Polemaster with several mounts.Fits the Orion Starshoot P1 alignment camera.
Shipping worldwide : +3 €
-
Par astrokraken le 11 Février 2018 à 00:26
This adapter allows to firmly attach
a finderscope to a fast-release
photo ball-head.Thanks to ist 41-34mm width x 6 mm height
its male dovetail fits the usual quick-release systems.Want to find out more ? Click on the pictures !
Suivre le flux RSS des articles de cette rubrique